Home > Gun Type > MI Products for Ruger® > Midwest Industries Inc Products for Ruger® 10/22® >

MI-1022-8H
MI 8.0" M-Lok™ Hand Guard Compatible with Ruger® 10/22 TakeDown®

MI-1022-8H<br>MI 8.0" M-Lok™ Hand Guard Compatible with Ruger® 10/22 TakeDown®


 
Alternative Views:


Our Price: $124.95

Stock Status:In Stock

Product Code: MI-1022-8H
Qty:

 
Midwest Industries Inc made hand guard for Ruger® 10/22 TakeDown® models.


Features
  • Lightweight design with a slim profile
  • True Free Float Design
  • Mounting bolt and wrench included
  • 8.0" overall length
  • 1.290" Inside Diameter
  • Two built in anti-rotation QD sockets
  • Features 8 sides of M-Lok slots
  • 5-slot polymer M-Lok rail included
  • Weight 7.3 oz installed
  • Construction from 6061 Aluminum, Type 3 Hard Coat Anodized for a lifetime of service
  • Fully dehorned for a non-abrasive, comfortable feel
  • MI Lifetime Warranty
  • 100% Made in America - Keeps America Working
  • US Patent Pending


Additional Installation Tips & Instructions
We have found during dozens of installations that there are variations in the Ruger
® firearms. These variations will in no way effect the function or performance of the Ruger® 10/22 TakeDown®. Please remember this firearm is a takedown model so perfect alignment may not always be achieved. We have found for best alignment, start by aligning the MI handguard with the top edges of the factory plastic stock. This may take a few attempts and some patience but will produce a very satisfactory result. Some firearms will also show a left or right cant with the whole barrel assembly when locked into place. You can see this by looking from the rear of the firearm and using the top rail as a reference surface. Neither the function of our handguard or the firearms performance will be effected by these slight alignment variations of the factory manufactured firearms. On a final note if after installing the handguard on your firearms you still have any play please check that the tension adjustment ring is properly adjusted on your rifle. Additional information and photos can be found on our website.



Only compatible with new Ruger® 10/22 TakeDown® models

Magpul® and M-LOK™ are trademarks of Magpul Industries Corp

Ruger®, PC9™ Carbine, 10/22 TakeDown®, 10/22®, and Ruger Precision® are trademarks of Sturm, Ruger & Company, Inc.



Average Rating: Average Rating: 4.5 of 5 4.5 of 5 Total Reviews: 2 Write a review »

  0 of 0 people found the following review helpful:
 
4 of 5 Hand guard is awesome. One miner issue September 3, 2019
Reviewer: Eric Wagstaff from Fort Ashby, WV United States  
The hand guard is awesome no issue there. It just the screws for mlok rail they supply will hit the barrel and mar it, if you want to use the slots close to the receiver for a red dot. Found out the hard way and had to file them down flush with mlok bolt.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Finally! you can add Front Sights to your Charger! July 10, 2019
Reviewer: Chris Sewell from Georgia  
I have been looking for a rail, or handguard or anything for mounting iron sights, to my Ruger Charger. Midwest did it. This rail is very similar to their famous rail for the Ruger PCC rifles. But it is a scaled down version for the Charger pistol. When mounting, I had to adjust the mount & rail a bit to make it line up evenly with the barrel, but it can be done easily. It installs in 5 minutes. The length allows for about 1 inch of barrel extending out of the rail. So you can easily add on your favorite barrel attachments! The rail adds minimal weight to the front end, but keeps the gun balanced, when used with an attached pistol brace. The great part is, you can Finally add on some iron sights to the Charger Pistol.  Flip up sights are kind of bulky, but a small set of stationary sights will work best. Then you also have several QD mounts for a shoulder strap.
I highly recommend it!

Was this review helpful to you?